TruckCraft Pickup Inserts
TC-100 Steel Pickup Insert
The TC-100 is manufactured to the highest quality standards. It is an addition to your pickup that you will be proud to own. Every feature has been designed and built tough to serve you better. Features include a seamless floor; a heavy-duty three-way tailgate; maintenance free power operation; a bed capable of handling a full sheet of plywood; and a finish that has been etched, primed and final coated to complement any truck. The unit can be installed in your truck, by you (no welding, no cutting; only two bolts and one cable), in less than two hours.
At TruckCraft, we are proud of the products we manufacture. We include a full three-year warranty with every model. And we know that the life of our units will usually outlast two or three new trucks. Compare the TC-100 features and become a proud TruckCraft owner. Municipalities and Landscaper must have body.
Specifications:
3 year warranty NEW!
2 models to fit standard 8' bed, or shortbed pickups
6,200 lb. dump capacity NEW!
2 Cu. Yd. capacity (5 Yd. with sideboards)
48.5" x 101" Cargo area
150 amp resettable in-line circuit breaker safeguards power in, and also allows manually switching off power under hood to disable unattended insert. NEW!
12 volt MONARCH HYDRAULICS™ Electro-Hydraulic system
47 degree dump angle
14 Ga. steel sides continuously welded to 12 Ga. steel floor, 10 Ga. tailgate. Two welded stake pockets on front bulkhead, and 16" removable corner standards to provide slots for side boards at rear. NEW!
Dumper weight- 750 lbs.
27 second cycle time
Options:
Available in shortbed model
Cab guard
Rollup tarp
Set of Side Boards NEW!
Aluma Tie Down Rail kit NEW!
TC-120 Ultra Aluminum Dump Insert
The TC - 120 ULTRA has been engineered from the ground up to provide users with years of maintenance free service. The body and frame are designed and constructed entirely of aluminum and stainless steel to provide durability and resistance to rust and corrosion. TruckCraft's innovative use of aluminum alloy extrusions welded to sheet aluminum enables them to offer a pickup dump insert that is 300 - 350 lbs. lighter than comparable steel units. The result is a unit that weighs less, hauls more payload, and will be less expensive to operate and maintain. This classy accessory for your pickup is the first of its kind available through nationwide distribution.
Rigid Floor of Extruded Aluminum - The floor is constructed of aluminum alloy plank extrusions that provide rigid reinforcement every 5". This "tongue and groove" design, proven in roll-back car carriers, keeps the floor from deflecting under heavy loads and eliminates the "washboard effect" seen in light-duty sheet-bed models.
Aluminum Rails add Overall Strength - The TC-120 design utilizes a polished and fluted aluminum alloy extrusion on the top box rall of the body sides and the top and bottom of the tailgate. This provides the maximum strength at a minimum weight while greatly enhancing the product's overall appearance.
Low Bed Height - only 3-1/4" above pickup bed - The 2.4 cubic yard payload offered by the TC - 120 is positioned only 3-1/4 inches above your pickup floor. This feature adds greater volume and keeps the vehicle's center of gravity low. It also reduces the height that heavy objects must be lifted into the bed.
All Aluminum Bed - 48 1/8" x 98" - The bed holds a full sheet of plywood with the tailgate closed. The side board installation kit (shown) used with your boards will increase the volumetric capacity from 2.4 cu. yds. to as much as 5 cu. yds.
Three-way Tailgate - The TC-120 tailgate has a paddle latch and can be opened and closed with just one hand. The gate can easily be removed for complete access. Control chains can be adjusted for using the tailgate as a spreader.
3 Stage Telescopic Lift and Cab Protector - The ULTRA hoist system utilizes a heavy duty, three stage, telescopic cylinder with chromed rod sections. The hoist has been custom designed by TruckCraft to lift 7,000 lbs. to a 47 degree dump angle in just 18 seconds. The aerodynamic cab protector (shown) provides low wind resistance and great visiblity. The cab protector and a full tarp system are options that can be easily added to the TC-120 at any time.
Power Unit and Standard Remote Dump Control - A compact, one-piece power unit is mounted directly behind the cab in close proximity to the hoist. The remote control buttons activate the motor/hydraulic pump from within the cab or up to 12 feet away from the cab. One 12 volt battery cable is the only electrical connection required.
150 amp resettable in-line circuit breaker- safeguards power in, and also allows manually switching off power under hood to disable unattended insert. NEW!
The TC-120 comes with a 3 year warranty NEW!
Insert weight- 420 lbs.
2 Hour installation
Options:
SlipStream Cab Guard
Rollup Tarp
Quick-Cover
Side Board Installation (Rigid)
Side Board Installation (Swing Away)
AlumaBoards 18" Sideboards
Orion Screened Bulkhead
TC-120 Short Bed Pickup Insert
Designed to fit most 6 1/2 foot Chevy/Ford/Dodge Shortbed pickups, the TC-120S ULTRA has been engineered to provide users with years of maintenance free service.
Fits most Chevy/Ford/Dodge 6 1/2' shortbed pickups
-
All aluminum T-6 tempered alloy and .125" formed sheet
-
All stainless hardware for custom look and lasting durability
- 7,000 lbs. dump capacity, 1.8 cubic yards volume
- Body raises to 55 degree dump angle in just 19 seconds
- 12 volt, self-contained, MONARCH HYDRAULICS™ electro-hydraulic unit
-
3 year factory warranty NEW!
- 150 amp resettable in-line circuit breaker NEW!
Options:
Orion Bulkhead
Sideboard Mount Kit
Quick Disconnect